Results 1 to 22 of 22
  1. 04.26.24, 8:49 PM #1
    jcolley
    jcolley is offline
    Member jcolley's Avatar
    Join Date
    08.05.10
    Location
    Portland, Maine
    Posts
    82
    Liked: 23

    Default Replacement PFC Rotors

    Going through my car and have one rotor that measures slightly tweaked, causing some drag.

    PFC Rotors 255.10.0042.03 and .04, Pegasus says no longer made.

    Any alternative rotors compatible with the PFC calipers?
    Reply With Quote Reply With Quote
  2. 04.26.24, 10:02 PM #2
    jcolley
    jcolley is offline
    Member jcolley's Avatar
    Join Date
    08.05.10
    Location
    Portland, Maine
    Posts
    82
    Liked: 23

    Default

    Nevermind, they appear to match dimensions of LD20 discs.
    Reply With Quote Reply With Quote
  3. 04.27.24, 7:46 PM #3
    BeerBudgetRacing
    BeerBudgetRacing is online now
    Classifieds Super License BeerBudgetRacing's Avatar
    Join Date
    09.04.13
    Location
    Goleta, California
    Posts
    4,307
    Liked: 1384

    Default

    Yes, but the PFC 2 groove floating disc we use on FCs w/LD20s is no longer made either.
    Reply With Quote Reply With Quote
  4. 04.27.24, 8:52 PM #4
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    If you cannot find them elsewhere, I should be able to make them for you.
    Reply With Quote Reply With Quote

  5. The following 2 users liked this post:

    BeerBudgetRacing, Steve Demeter
  6. 05.01.24, 11:57 AM #5
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    I'll be receiving a sample rotor in the next few days to make a drawing from, so if anyone needs replacement rotors, I'll be able to make them quickly.
    Reply With Quote Reply With Quote

  7. The following 2 users liked this post:

    10rmotor, BeerBudgetRacing
  8. 05.01.24, 5:20 PM #6
    jcolley
    jcolley is offline
    Member jcolley's Avatar
    Join Date
    08.05.10
    Location
    Portland, Maine
    Posts
    82
    Liked: 23

    Default

    Quote Originally Posted by R. Pare View Post
    I'll be receiving a sample rotor in the next few days to make a drawing from, so if anyone needs replacement rotors, I'll be able to make them quickly.
    I'm likely in for a set of 4.
    Reply With Quote Reply With Quote
  9. 05.01.24, 6:44 PM #7
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    I'll post again once I have a drawing ( and check my stock of blanks, of course!).
    Reply With Quote Reply With Quote
  10. 05.10.24, 10:50 AM #8
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    Have the PFC rotors, and have made the drawings. Price should end up somewhere right around $200 each. I'm hoping to do decent sized batch so that the raw material cost can come down a bit.

    If anyone is interested, message me.
    Reply With Quote Reply With Quote

  11. The following members LIKED this post:

    BrianT1
  12. 05.10.24, 2:52 PM #9
    jcolley
    jcolley is offline
    Member jcolley's Avatar
    Join Date
    08.05.10
    Location
    Portland, Maine
    Posts
    82
    Liked: 23

    Default

    Quote Originally Posted by R. Pare View Post
    Have the PFC rotors, and have made the drawings. Price should end up somewhere right around $200 each. I'm hoping to do decent sized batch so that the raw material cost can come down a bit.

    If anyone is interested, message me.
    In for a set of four, will send you PM.

    Are these side specific like the PFCs or generic?
    Reply With Quote Reply With Quote
  13. 05.10.24, 5:05 PM #10
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    You can have them either way - if face grooved, they will be handed. Not grooved = not handed. $25 extra for the grooving.

    Will hopefully get a quote for a batch of blanks come Monday or Tuesday.
    Last edited by R. Pare; 05.10.24 at 5:26 PM.
    Reply With Quote Reply With Quote
  14. 05.15.24, 4:29 PM #11
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    Quote came in just now. Rotor price will be $190 non-grooved.

    For those who want sets, let me know and I'll get the material in and get production going.
    Reply With Quote Reply With Quote

  15. The following members LIKED this post:

    BLS
  16. 05.23.24, 8:21 PM #12
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    Material is ordered and most likely will be here week after next.
    Reply With Quote Reply With Quote
  17. 06.10.24, 12:55 PM #13
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    The material just arrived and I'll be starting on them later today.
    Reply With Quote Reply With Quote
  18. 06.13.24, 6:56 AM #14
    FASTDAD
    FASTDAD is offline
    Senior Member FASTDAD's Avatar
    Join Date
    10.03.07
    Location
    Cannon Falls, MN
    Posts
    236
    Liked: 40

    Default Steel type

    Good morning to all,
    Curious minds want to know, what kind/type/no. of steel are the rotors made from?
    Thanks a lot.
    Todd
    I would rather be making racing news than reading it. Living the dream out here in the middle of farm country
    Reply With Quote Reply With Quote
  19. 06.13.24, 10:33 AM #15
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    Ductile 80
    Reply With Quote Reply With Quote
  20. 06.13.24, 3:15 PM #16
    FASTDAD
    FASTDAD is offline
    Senior Member FASTDAD's Avatar
    Join Date
    10.03.07
    Location
    Cannon Falls, MN
    Posts
    236
    Liked: 40

    Default Thanks

    Thanks for info about the rotors, good to know this stuff.
    Todd
    I would rather be making racing news than reading it. Living the dream out here in the middle of farm country
    Reply With Quote Reply With Quote
  21. 06.13.24, 5:18 PM #17
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    You can pay me back by ordering some!
    Reply With Quote Reply With Quote
  22. 07.09.24, 10:16 PM #18
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    Am finally on the last lathe operation for these. If anyone wants any, let me know!
    Reply With Quote Reply With Quote
  23. 07.10.24, 4:22 PM #19
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    Whomever it was who wanted 2 car sets of rotors, message me - I somehow lost your email!
    Reply With Quote Reply With Quote
  24. 09.19.24, 9:08 PM #20
    janton9736
    janton9736 is offline
    Member
    Join Date
    06.02.22
    Location
    Wheaton, Illinois
    Posts
    83
    Liked: 6

    Default

    Quote Originally Posted by R. Pare View Post
    Whomever it was who wanted 2 car sets of rotors, message me - I somehow lost your email!
    Any more left for the PFM?
    Reply With Quote Reply With Quote
  25. 09.20.24, 9:37 AM #21
    R. Pare
    R. Pare is offline
    Senior Member
    Join Date
    08.18.02
    Location
    Indy, IN
    Posts
    6,346
    Liked: 1972

    Default

    Have plenty left. Just have to machine the slots, if the customer wants them.
    Reply With Quote Reply With Quote
  26. 10.10.24, 8:50 PM #22
    Richard Hybels
    Richard Hybels is offline
    Contributing Member
    Join Date
    09.13.02
    Location
    San Francisco
    Posts
    581
    Liked: 105

    Default Rotors

    I had a rotor come apart at Laguna a few weeks ago so I’ll be examining and replacing soon. Having a rotor come apart and tear the caliper off not a good thing at 100 mph.
    I've never seen that happen in 25 years of FF.
    Attached Thumbnails Attached Thumbnails Click image for larger version.  Name: IMG_4134.jpg  Views: 100  Size: 179.4 KB  ID: 112793  
    Hybels
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Thread Information

Users Browsing this Thread

There are currently 5 users browsing this thread. (0 members and 5 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules





About Us
Since 2000, ApexSpeed.com has been the go-to place for amateur road racing enthusiasts, bringing together a friendly community of racers, fans, and industry professionals. We're all about creating a space where people can connect, share knowledge, and exchange parts and vehicles, with a focus on specific race cars, classes, series, and events. Our community includes all major purpose-built road racing classes, like the Sports Car Club of America (SCCA) and various pro series across North America and beyond. At ApexSpeed, we're passionate about amateur motorsports and are dedicated to helping our community have fun and grow while creating lasting memories on and off the track.
Site Info
Terms and Conditions
Forum Rules
Privacy Policy
Current Advertisers
Advertising Information
Reset Lost Password
Social