flatshifter expert and custom shifter kit for Stohr

[urbanimports02]

we have a flat shifter expert kit for sale. was installed with a custom bump shift kit in a stohr car with Kawasaki zx10r. would need to change out the spindle piece on the blipper for use on a gsxr. $600

custom bump shift kit for stohr fb. cnc machined aluminum clamp on bearing housing for the shift lever installs with no cutting or welding. clamp on cable mount can be installed in any position for use with or without the shift load sensor. cnc machined shift lever and knob setup for comfortable hand postion with the knob slightly tilted inward. cable is a custom made cable to the same spec as a swift formula atlantic. it is much higher quality then anything that has ever came out of the stohr factory and holds up to heat and is very low drag. includes mounts for the motor end (chassis mount to factory location) as well as motor end lever. $500 or $1000 for all

[10rmotor]

Jesse, what/who is the mfr of this cable? What size is it? I'm guessing the standard stohr cable is the generic california push/pull cable item?

[urbanimports02]

the stohr cables are some sort of off the shelf morse type cable. they simply slide into a groove and hold them in with safety wire. so the jacket mount is far from solid and allows the cable to change alignment etc. the cable is also very "draggy" compared to this one. the cable they use is nowhere near as high temp capable as this one. in the swift, the cable runs right through the header primaries with a simple silicone jacket for heat protection. this cable also uses nice solid bulkhead mounts for solid mounting to the chassis/gearbox at either end. the cable we use is made by control cables inc. to custom specs. I can not even say for sure what the build spec is as it was passed onto me buy a swift engineer. essentially I was authorized to use their build spec which I used on West cars at the time(I was working for both West and a pro atlantic team at the time). the result was a much more solid feeling connection between the shifter and the gearbox. feels as solid as direct rod connection with just a little free play. the morse style cables feel spongy like the cable is stretching. these cables are double the cost, but last exponentially longer and feel a ton better. basically worth every penny!! both cables are 1/4"

[10rmotor]

Thanks for the info Jesse I'll check them out.

[J Somers]

Jesse,
Interested in the Flatshifter if still available. I will give you a call later today.

Thank you,
Jason

[petawawarace]

Sent a pm a few days ago about the flatshift and haven't heard back???

[urbanimports02]

Sorry guys, busy this week with dry sump orders and lost a fuel lift pump in the truck so I wasn't paying attention to my messages here. I will try to get back to you guys in order of pm's. Thanks

[argoraffo]

we have a flat shifter expert kit for sale. was installed with a custom bump shift kit in a stohr car with Kawasaki zx10r. would need to change out the spindle piece on the blipper for use on a gsxr. $600

custom bump shift kit for stohr fb. cnc machined aluminum clamp on bearing housing for the shift lever installs with no cutting or welding. clamp on cable mount can be installed in any position for use with or without the shift load sensor. cnc machined shift lever and knob setup for comfortable hand postion with the knob slightly tilted inward. cable is a custom made cable to the same spec as a swift formula atlantic. it is much higher quality then anything that has ever came out of the stohr factory and holds up to heat and is very low drag. includes mounts for the motor end (chassis mount to factory location) as well as motor end lever. $500 or $1000 for all

Jesse,
I sent a phone message to you asking it both are still for sale and left my email address.
Ian in South Australia.

[urbanimports02]

I am pretty sure both are spf. I am out of town until Friday so expect I should have payment upon my return. I will post both as sold as soon as it's final. Thanks