Bad switch, bad ground, broken wire. Electrical is so fun to chase.
Will
Type: Posts; User: Vulnavia
Bad switch, bad ground, broken wire. Electrical is so fun to chase.
Will
4'x2' table w/ folding legs. Glass cleaner, box/rolls paper towels.ect. Everything in your garage ! I bring a death wheel grinder, sawzall , drill and bits, small mig welder, ( Think spec racers...
Anyone have a phone number for Leon or Jeremy?
Thanks,
Will
Then you use new bolts from Suzuki?
Will
Where can you get aftermarket connecting rod bolts for a gsx r600? Can't find them on the ARP website.
Thanks,
Will
How much [from idle?] rpm is required for a smooth down shift? What range?
Thanks,
Will
Thanks,
Will
The first number is disconnected, the other goes to voicemail. Is he hard to get a hold of [called several times] or just really busy?
and Thanks Jay.
Will
Anyone have a working phone number?
Thanks,
Will
I didn't think so.
Thanks for the offer, don't have an engine to use it on.
Will
Confused about using the up to 2013 engine - rule. If the newer engines are the same 2011 to 2020 can you use a 2015?
Thanks,
Will
Advice on reusing head gasket. Also, connecting rod failure. Broke near the bolt head.
Thanks,
Will
That's a start.
Thanks,
Will
Thanks Cory.
Have to add weight to the car [MC powered] to make 900# and don't have good scales. I know the weight with a 593,
so I will need to add to get to 900#. wondering appox. how much before...
Anyone know the weight of a 593 and the weight of a suzuki 600
will
Anyone have a drawing of this years restrictor [28mm?]
Thanks,
Will
3 or 4 years. I have had the motor running recently. Just figured a good cleaning would help.
Thank You for the link.
Will
Looking for ideas on the best way to clean injectors. [ they have been sitting with fuel in them for quite some time]
Thanks,
Will
George,
Thank you for the reply and part number. Have ordered, should be here Friday.
Was hoping to use the sending unit hole. Looks like its a pipe thread [tapered] .9mm pitch not sure of the...
Where, what port do you get your oil pressure from? GSX R600 Also, anyone know what thread/pitch is the oil pressure sending unit is?Thanks, Will
Very helpful.
Thank You
Will
It's a MC engine with a generator. So a two post switch as suggested would be ok?
will
Which one to use? Switch with or without alternator protection ?
Will
Thoughts on disabling/eliminating
Side stand switch
Tip over sensor
Excva
Thanks,
Will
Thanks Dan and Eric
I have already plumbed the oil cooler as suggested, was not sure of the proper way to seal the stock oil/water cooler, if a "passage" was required. Did not want to do that wrong!...
If I understand correctly, using the ports above the oil pan, right side of engine, use the flat plate with O ring. No "passage" needed.
Thanks, Dan
Will
George,
Thank you for checking. It seems to me that the oil flowing through the cooler goes up to the generator and pistons.
Probably important.
Thanks again ,
Will
So the plate blocks the two ports from the engine?
Will
Thanks George,
I see the o ring on the stock oil cooler, is there no need for a "passage" in the flat plate?
Thanks again,
Will
Oil cooler blanking plate, just a flat plate?
Thanks, Will
Anyone know which sensors are not needed to run the engine?
Thanks,
Will
Many Thanks Russ,
Will
Close to wiring the engine. On the stock wiring harness what is needed and what is not needed to run the engine.
I know sending it to Hyper is one answer, but I had a less than pleasant experience...
what sensors are needed, and which ones are not needed to run the engine.
Will
TDI pilot, Thank you, you have been very helpful, Will
Ready to start fuel plumbing. What size and type of hose is required. Thanks, Will
Thanks, Will
Have all the fittings and hose. Just want to plumb the right line to the top of the heat exchanger.
Thanks,
Will
which is which? Don't have a manual with me.
Thanks,
Will
The ports under the clutch, is one an inlet, one an outlet
Will
Suzuki
Spoke with a engine builder about making the engine "reliable" and it sounded like some internal modifications, more than just changing out rod bolts, are required. I was under the impression any...
Thanks,
Will
Where can I find a drawing of the restrictor plate.
Thanks, Will
Anyone know where one can purchase header flanges ?
Thanks,
Will
Any one know Bill Butterworth ?
Will
Ideas for a Dash. What would be needed at a minimum, to keep the engine safe.
RPM, Shift light, Oil pressure ?
Thanks,
Will
Thanks,
Will
Have been told it is Stainless steel, and Ti. The bike dealers don't know.
Thanks,
Will
Thanks.
Went on a GSX r600 forum and found the bike guys using a Russell Performance
# 640860.
Engine I have, after looking at it actually has one :mad:.
Thanks again,
Will